Mounting iSCSI LUNs to a Windows client

1. Use Windows Remote Desktop to connect to the Windows client on which you want to mount the iSCSI LUN. For more information, see Connect to your Windows instance using RDP in the Amazon Elastic Compute Cloud User Guide.

2. Open a Windows PowerShell as an Administrator. Use the following commands to enable iSCSI on your Windows instance and configure the iSCSI service to start automatically.

   PS C:\> Start-Service MSiSCSI 
   PS C:\> Set-Service -Name msiscsi -StartupType Automatic 

3. Retrieve the initiator name of your Windows instance. You’ll use this value in configuring iSCSI on your FSx for ONTAP file system using the NetApp ONTAP CLI.

   PS C:\> (Get-InitiatorPort).NodeAddress

   The system responds with the initiator port:

   iqn.1991-05.com.microsoft:ec2amaz-abc123d 

4. To enable your clients to automatically failover between your file servers, you need install Multipath-IO (MPIO) on your Windows instance. Use the following command:

   PS C:\> Install-WindowsFeature Multipath-IO

5. Restart your Windows instance after the Multipath-IO installation has completed. Keep your Windows instance open to perform steps for mounting the iSCSI LUN in a section that follows.

1. Connect to the NetApp ONTAP CLI on the FSx for ONTAP file system on which you created the iSCSI LUN using the following command. For more information, see Using the NetApp ONTAP CLI.

   ~$ ssh fsxadmin@your_management_endpoint_ip

2. Using the NetApp ONTAP CLI lun igroup create, create the initiator group, or igroup. An initiator group maps to iSCSI LUNs and controls which initiators (clients) have access to LUNs. Replace host_initiator_name with the initiator name from your Windows host that you retrieved in the previous procedure.

   ::> lun igroup create -vserver svm_name -igroup igroup_name -initiator host_initiator_name -protocol iscsi -ostype windows

   If you want to make the LUNs mapped to this igroup available to multiple hosts, you can specify multiple comma-separated initiator names. For more information, see lun igroup create in the NetApp ONTAP Documentation Center.

3. Confirm the igroup was created successfully using the following command:

   ::> lun igroup show

   The system responds with the following output:

   Vserver    Igroup        Protocol OS Type  Initiators 
   ---------  ------------  -------- -------- ------------------------------------ 
   svm_name   igroup_name   iscsi    windows  iqn.1994-05.com.windows:abcdef12345

   With the igroup created, you are ready to create LUNs and map them to the igroup.

4. This step assumes that you have already created an iSCSI LUN. If you have not, see Creating an iSCSI LUN for step-by-step instructions to do so.

   Create a LUN mapping from the LUN to your new igroup.

   ::> lun mapping create -vserver svm_name -path /vol/vol_name/lun_name -igroup igroup_name -lun-id lun_id

5. Confirm that the LUN is created, online, and mapped with the following command:

   ::> lun show -path /vol/vol_name/lun_name 
   Vserver     Path                            State   Mapped   Type     Size 
   ---------   ------------------------------- ------- -------- -------- -------- 
   svm_name    /vol/vol_name/lun_name          online  mapped   windows  10GB 

   You are now ready to add the iSCSI target on your Windows instance.

6. Retrieve the IP addresses of the iscsi_1 and iscsi_2 interfaces for your SVM using the following command:

   ::> network interface show -vserver svm_name

               Logical    Status     Network            Current       Current Is 
   Vserver     Interface  Admin/Oper Address/Mask       Node          Port    Home 
   ----------- ---------- ---------- ------------------ ------------- ------- ---- 
   svm_name 
               iscsi_1    up/up      172.31.0.143/20    FSxId0123456789abcdef8-01 
                                                                      e0e     true 
               iscsi_2    up/up      172.31.21.81/20    FSxId0123456789abcdef8-02 
                                                                      e0e     true 
               nfs_smb_management_1 
                          up/up      198.19.250.177/20  FSxId0123456789abcdef8-01 
                                                                      e0e     true 
   3 entries were displayed.

   In this example, the IP address of iscsi_1 is 172.31.0.143 and iscsi_2 is 172.31.21.81.

1. On your Windows instance, open a PowerShell terminal as an Administrator.

2. You will create a .ps1 script that does the following:

   • Connects to each of your file system’s iSCSI interfaces.

   • Adds and configures MPIO for iSCSI.

   • Establishes 8 sessions for each iSCSI connection, which enables the client to drive up to 40 Gb/s (5,000 MB/s) of aggregate throughput to the iSCSI LUN. Having 8 sessions ensures a single client can drive the full 4,000 MB/s throughput capacity for the highest-level FSx for ONTAP throughput capacity. You can optionally change the number of sessions to a higher or lower number of sessions (each session provides up to 625 MB/s of throughput) by modifying the script's for-loop in the #Establish iSCSI connection step from 1..8 to another upper-bound. For more information, see Amazon EC2 instance network bandwidth in the Amazon Elastic Compute Cloud User Guide for Windows Instances.

   Copy the following set of commands into a file to create the .psl script.

   • Replace iscsi_1 and iscsi_2 with the IP addresses you retrieved in the previous step.

   • Replace ec2_ip with the IP address of your Windows instance.

   #iSCSI IP addresses for Preferred and Standby subnets 
   $TargetPortalAddresses = @("iscsi_1","iscsi_2") 
                                       
   #iSCSI Initator IP Address (Local node IP address) 
   $LocaliSCSIAddress = "ec2_ip" 
                                       
   #Connect to FSx for NetApp ONTAP file system 
   Foreach ($TargetPortalAddress in $TargetPortalAddresses) { 
   New-IscsiTargetPortal -TargetPortalAddress $TargetPortalAddress -TargetPortalPortNumber 3260 -InitiatorPortalAddress $LocaliSCSIAddress 
   } 
                                       
   #Add MPIO support for iSCSI 
   New-MSDSMSupportedHW -VendorId MSFT2005 -ProductId iSCSIBusType_0x9 
                                       
   #Establish iSCSI connection 
   1..8 | %{Foreach($TargetPortalAddress in $TargetPortalAddresses)
   {Get-IscsiTarget | Connect-IscsiTarget -IsMultipathEnabled $true -TargetPortalAddress $TargetPortalAddress -InitiatorPortalAddress $LocaliSCSIAddress -IsPersistent $true}}
                                       
   #Set the MPIO Policy to Round Robin 
   Set-MSDSMGlobalDefaultLoadBalancePolicy -Policy RR 

3. Launch the Windows Disk Management application. Open the Windows Run dialog box, and enter diskmgmt.msc and press Enter. The Disk Management application opens.

   

4. Locate the unallocated disk This is the iSCSI LUN. In the example, Disk 1 is the iSCSI disk. It is offline.

   

   Bring the volume online by placing the cursor over Disk 1 and right-click then choose Online.

   Note

   You can modify the storage area network (SAN) policy so that new volumes are automatically brought online. For more information, see SAN policies in the Microsoft Windows Server Command Reference.

5. To initialize the disk, place the cursor over Disk 1 right-click, and choose Initialize. The Initialize dialog appears. Choose OK initialize the disk.

6. Format the disk as you would normally. After formatting is complete, the iSCSI drive appears as a usable drive on the Windows client.

To validate your iSCSI configuration

1. Open a Windows PowerShell window.

2. Download the script using the following command.

   PS C:\> Invoke-WebRequest "https://docs.aws.amazon.com/fsx/latest/ONTAPGuide/samples/CheckiSCSI.zip" -OutFile "CheckiSCSI.zip"

3. Expand the zip file using the following command.

   PS C:\> Expand-Archive -Path ".\CheckiSCSI.zip" -DestinationPath "./"

4. Run the script using the following command.

   PS C:\> ./CheckiSCSI.ps1

5. Review the output to understand your configuration's current state. The following example demonstrates a successful iSCSI configuration.

   PS C:\> ./CheckiSCSI.ps1
   
   This script checks the iSCSI configuration on the local instance.
   It will provide information about the number of connected sessions, connected file servers, and MPIO status.
                               
   MPIO is installed on this server.
                               
   Initiator: 'iqn.1991-05.com.microsoft:ec2amaz-d2cebnb'
   to Target: 'iqn.1992-08.com.netapp:sn.13266b10e61411ee8bc0c76ad263d613:vs.3'
   has 16 total sessions (16 active, 0 non-active)
   spread across 2 node(s).
   MPIO: Yes